Dry battery can be called as battery MF Battery (battery maintenance free), because by using dry battery we are easier to do the maintenance and also free positioning slanted or upright will not be a problem.
dry batteries and wet batteries actually have the same functionality in terms of amperage capacities ranging from high to low and the difference only in terms of efficient course. but when compared with wet batteries, MF batteries have a pretty good advantage because the material using special spare parts that resist corrosion. But if seen from the price of dry batteries a little more expensive than wet batteries .
We need to know that when using a dry battery, we also need to learn how to fix it. Because without knowing it we will spend a very expensive cost to repair the battery. things to note before making a repair or battery service is to prepare some tools and materials to be used. Tools and materials are not complicated and very easy to get. Here are some tools and materials that need to be prepared:
•Fluid Accu
•Screwdriver
•Plastic glue
•Plastic injections / SPED
Find a new battery liquid and usually used to fill the new battery. Because usually the composition of the battery water is different from that used to increase the battery. Using a used ink or other used printer ink is also allowed. after the tools and materials are ready, following step steps how to fix the dry battery. (read also: smoke discharge on the motor)
Cara Memperbaiki Aki Kering Motor :
1. Disassemble the battery
The battery to be repaired should be cleaned first. Clean the outside of the battery, so that the dirt or material that sticks to the battery is lost. How to clean it with a cloth that has been provided. After cleaning, it's time to open the battery .
How to open it quite easily by using a screwdriver. Congkel is the battery cover until it opens. It takes power to pry the battery, especially the lid on the battery is difficult to open. the most important at the time of the process of opening the battery do not break, difficult to cause the battery leak. (read also: side oil function on motorcycle)
And if it gets damaged it will be difficult to replace it because its spare parts also do not exist. Can also be done with modifications but it takes a long time and less efficient .
2. Charge the Battery Water
Then after the battery cover open prepare the injection and also a washcloth that has been provided. At the time will fill the battery check your battery first. Make sure already open the rubber hole on the battery. usually there are about 3-10 holes rubber depending on amperenya capacity .
The more the rubber hole the greater the amperage capacity and there are many cells in it. For the way of charging is, prepare the battery water and make the battery water on the injection. then if already insert the injection that contains the battery water into the rubber hole on the battery with a distance of up to 1cm below the hole. Do the filling until evenly and try full .
If it is tightly sealed rubber parts and make sure it is not easy to reopen. Check the battery that has been filled then try to close tightly and there is no leak on the battery. After the charging process is complete, reattach the battery cover so that the battery looks like new. make sure the closing is tight. If the lid is cracked or a little damage can be attached to the plastic glue you have provided. (read also: how to overcome difficult motor distarter)
3. Mengisi Daya Listrik Aki
The next process that will be done is to fill the power voltage or jug can be called giving stun on the battery. This process is a charging process, the same thing when we are charging hp or laptop with adapter. But in addition there is also more charging battery using a motor battery. so there are 2 ways that is with the battery and use other motor batteries. (Also read: causes of wasteful motorcycles)
• Fill the battery
The first is how to charge the battery by using battery charger. Using a battery charger adapter is very efficient in charging it. This tool is the same thing with the transformer used in cas hp or laptop. However, in the case of battery life and amperage capacity must be larger .
Tools have been widely sold by the seller of the battery and widely used by the service of battery stun and battery service workers. The same way with the process of charging like you do on hp dll. better when using this method is an indicator if the power is fully charged to the battery and the battery is ready for use. (read also: excess tires filled with nitrogen)
• Jamper on Motor Battery
Next is how to jamper on other motor battery. Keep in mind that if using this method should see the resources used in the battery prime. The way to do with menjamper battery and turn on your motor vehicle. Turn on the machine in less than 30 minutes to 1 hour
Using this method is not as efficient as using cas. With jamper on other motorcycle batteries, there is at least some initial power for the battery that will be charged before being used on your vehicle. after you fill and you plug in your motor, try to also do the motor machine in a stationary position before you use another device on your motor to the position of the battery used stable. (read also: most big and cool motor)
Dry batteries that are currently often used on motor vehicles are notoriously anti-maintenance, but all things certainly have an active period or duration of use. One to see the time period of this battery by checking regularly in terms of cleanliness. as good as any battery that we have if not on guard will be quickly damaged.
Keep batteries clean routinely needs to be done then try before memakain vehicle be sure to melakukn heating to the vehicle engine. This applies to all vehicles, motorcycles and motorcycles that use dry batteries or MF batteries, especially. check also vehicle fuses, both in the arrangement of the cable. If a little looks chaotic then it will cause a zipper on your motor vehicle .
So some How to Fix Auto Dry Battery. Indeed, by doing some of the above does not guarantee that the repaired batteries like new again. but if we look and follow the appropriate way above will get maximum results on the battery as long as it does not happen on the fatal physical damage to the previous battery. May be useful.
dry batteries and wet batteries actually have the same functionality in terms of amperage capacities ranging from high to low and the difference only in terms of efficient course. but when compared with wet batteries, MF batteries have a pretty good advantage because the material using special spare parts that resist corrosion. But if seen from the price of dry batteries a little more expensive than wet batteries .
We need to know that when using a dry battery, we also need to learn how to fix it. Because without knowing it we will spend a very expensive cost to repair the battery. things to note before making a repair or battery service is to prepare some tools and materials to be used. Tools and materials are not complicated and very easy to get. Here are some tools and materials that need to be prepared:
•Fluid Accu
•Screwdriver
•Plastic glue
•Plastic injections / SPED
Find a new battery liquid and usually used to fill the new battery. Because usually the composition of the battery water is different from that used to increase the battery. Using a used ink or other used printer ink is also allowed. after the tools and materials are ready, following step steps how to fix the dry battery. (read also: smoke discharge on the motor)
Cara Memperbaiki Aki Kering Motor :
1. Disassemble the battery
The battery to be repaired should be cleaned first. Clean the outside of the battery, so that the dirt or material that sticks to the battery is lost. How to clean it with a cloth that has been provided. After cleaning, it's time to open the battery .
How to open it quite easily by using a screwdriver. Congkel is the battery cover until it opens. It takes power to pry the battery, especially the lid on the battery is difficult to open. the most important at the time of the process of opening the battery do not break, difficult to cause the battery leak. (read also: side oil function on motorcycle)
And if it gets damaged it will be difficult to replace it because its spare parts also do not exist. Can also be done with modifications but it takes a long time and less efficient .
2. Charge the Battery Water
Then after the battery cover open prepare the injection and also a washcloth that has been provided. At the time will fill the battery check your battery first. Make sure already open the rubber hole on the battery. usually there are about 3-10 holes rubber depending on amperenya capacity .
The more the rubber hole the greater the amperage capacity and there are many cells in it. For the way of charging is, prepare the battery water and make the battery water on the injection. then if already insert the injection that contains the battery water into the rubber hole on the battery with a distance of up to 1cm below the hole. Do the filling until evenly and try full .
If it is tightly sealed rubber parts and make sure it is not easy to reopen. Check the battery that has been filled then try to close tightly and there is no leak on the battery. After the charging process is complete, reattach the battery cover so that the battery looks like new. make sure the closing is tight. If the lid is cracked or a little damage can be attached to the plastic glue you have provided. (read also: how to overcome difficult motor distarter)
3. Mengisi Daya Listrik Aki
The next process that will be done is to fill the power voltage or jug can be called giving stun on the battery. This process is a charging process, the same thing when we are charging hp or laptop with adapter. But in addition there is also more charging battery using a motor battery. so there are 2 ways that is with the battery and use other motor batteries. (Also read: causes of wasteful motorcycles)
• Fill the battery
The first is how to charge the battery by using battery charger. Using a battery charger adapter is very efficient in charging it. This tool is the same thing with the transformer used in cas hp or laptop. However, in the case of battery life and amperage capacity must be larger .
Tools have been widely sold by the seller of the battery and widely used by the service of battery stun and battery service workers. The same way with the process of charging like you do on hp dll. better when using this method is an indicator if the power is fully charged to the battery and the battery is ready for use. (read also: excess tires filled with nitrogen)
• Jamper on Motor Battery
Next is how to jamper on other motor battery. Keep in mind that if using this method should see the resources used in the battery prime. The way to do with menjamper battery and turn on your motor vehicle. Turn on the machine in less than 30 minutes to 1 hour
Using this method is not as efficient as using cas. With jamper on other motorcycle batteries, there is at least some initial power for the battery that will be charged before being used on your vehicle. after you fill and you plug in your motor, try to also do the motor machine in a stationary position before you use another device on your motor to the position of the battery used stable. (read also: most big and cool motor)
Dry batteries that are currently often used on motor vehicles are notoriously anti-maintenance, but all things certainly have an active period or duration of use. One to see the time period of this battery by checking regularly in terms of cleanliness. as good as any battery that we have if not on guard will be quickly damaged.
Keep batteries clean routinely needs to be done then try before memakain vehicle be sure to melakukn heating to the vehicle engine. This applies to all vehicles, motorcycles and motorcycles that use dry batteries or MF batteries, especially. check also vehicle fuses, both in the arrangement of the cable. If a little looks chaotic then it will cause a zipper on your motor vehicle .
So some How to Fix Auto Dry Battery. Indeed, by doing some of the above does not guarantee that the repaired batteries like new again. but if we look and follow the appropriate way above will get maximum results on the battery as long as it does not happen on the fatal physical damage to the previous battery. May be useful.
No comments:
Post a Comment